JUST HOW TO REPLACE A BATH TUB

Just How to Replace a Bath Tub

Just How to Replace a Bath Tub

Blog Article

Book-Now

The publisher is making a number of good observations on Tools You Need to Install a New Bathtub as a whole in the content in the next paragraphs.


Tools You Need to Install a New Bathtub
Installing a tub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and also often, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably difficult task. If the old bathtub is readily obtainable, the task can relocate easily; if you have to open a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the new one. Make certain you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your washroom if you have already purchased a brand-new bathtub and do not require to change the setup of your previous supply of water pipelines.
Your devices as well as product list must consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Planning for the Installment


    To start with, the supporting frame supplied with the bath should be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid stress on the bathtub.
    Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you utilize all of the supplied washers.
    Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its last setting.

    Removing Old Touches


    If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is detach the water supply. After doing so, activate the faucets to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited accessibility that is usually the instance.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning throughout this procedure. Once the faucets have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
    Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.

    Setting up the Tub


    Utilizing both wood boards under its feet, position the tub in the required placement. The wood boards are practical in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small factors.
    The next objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the level as well as readjusting the feet on the bath tub till the spirit level checks out level.
    To install faucets, fit the bottom of the furthest flexible faucet connector to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Activate the water system and check all joints and also brand-new pipework for leakages and also tighten them if required. Load the bath tub and additionally check the overflow electrical outlet and also the regular outlet for leakages.
    Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub needs to wait up until the bathtub has actually been utilized at least once as this will certainly settle it into its final position.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
    If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
    Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washers are in area between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former type should be attached to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a stiff seal, causing the water to pass through the wall surface between the bathroom and also the tiling, leading to problems with wetness and possible leaks to the ceiling listed below.
    You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are offered in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealer can fracture rather early if you do not think about this movement before sealing.
    Additionally, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the market. It is a good idea to fit the tiles using water-resistant or water resistant sticky as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Tools You Need to Install a New Bathtub

    As a keen person who reads on How to Install a Bathtub Yourself, I thought sharing that portion was worthwhile. Enjoyed our blog? Please share it. Let others find it. Thank you so much for your time invested reading it.



    Click Here To Read More

    Report this page